Doepfer A-190-1 MIDI-CV/Gate/Sync Interface Bedienungsanleitung

doepferSystem A - 100MIDI-CV/SYNC Interface A-19011. IntroductionThe A-190 is a MIDI-CV/SYNC Interface, with whichyou can control any A-100 Module

A-190 MIDI-CV/SYNC InterfaceSystem A - 100doepfer10CLOCK TIMEThis parameter sets the amount by which the MIDIclock is divided before being sent to t

doepferSystem A - 100MIDI-CV/SYNC Interface A-19011REF. OFFSETThis parameter sets the voltage offset for the bottomnote - and works in the same way

A-190 MIDI-CV/SYNC InterfaceSystem A - 100doepfer12RTRIG. TIMEThis parameter sets the gate retrigger time - ie. thetime that elapses before another

doepferSystem A - 100MIDI-CV/SYNC Interface A-19013ASSIGN CV2This parameter sets which MIDI message is sent toDAC 2, and thus to the CV2 output sock

A-190 MIDI-CV/SYNC interfaceSystem A - 100doepfer144.3 PERFORMANCE MenusCHANNELThe CHANNEL parameter sets the MIDI receivechannel. MIDI messages re

doepferSystem A - 100MIDI-CV/SYNC interface A-19015GLIDE TIMEThe Glide Time parameter controls the length of theportamento time in the A-190’s built

A-190 MIDI-CV/SYNC interfaceSystem A - 100doepfer16No function at presentReserved for future expansion (e.g. arpeggiator)BEND WIDTHThe BEND WIDTH pa

doepferSystem A - 100MIDI-CV/SYNC interface A-190174.4 Storing set-upsThe A-190 is equipped with a non-volatile memory(EEPROM - electrically erasea

A-190 MIDI-CV/SYNC interfaceSystem A - 100doepfer184.5 PERFORMANCE modeIn performance mode the A-190 converts incomingMIDI messages into CV and ga

doepferSystem A - 100MIDI-CV/SYNC interface A-19019CONTROLLER #68 (Legato)The retrigger function (see CONFIG menu 1) canalso be switched on and off

A-190 MIDI-CV/SYNC InterfaceSystem A - 100doepfer22. OverviewControls and indicators1 Group : Button to select which menu section(out of the Confi

A-190 MIDI-CV/SYNC interfaceSystem A - 100doepfer204.6 Initialisation (Reset)When the A-190 is first switched on after leaving thefactory, its memo

doepferSystem A - 100MIDI-CV/SYNC interface A-19021Parameter Value NotesCHANNEL 0 MIDI channel 1REF. NOTE 36 C3CLOCK TIME 1 clock frequency at outpu

A-190 MIDI-CV/SYNC interfaceSystem A - 100doepfer22Controller Effect SettingCont 01 nModulationn = LFO voltage amount sent to CV 1Cont 05 nGlid

doepferSystem A - 100MIDI-CV/SYNC Interface A-1903In / Outputs! MIDI THRU : Output for relaying MIDI messagessent to MIDI IN to another MIDI unit.&

A-190 MIDI-CV/SYNC InterfaceSystem A - 100doepfer43. Starting to use the A-190Before switching your system on, use a MIDI cable toconnect between y

doepferSystem A - 100MIDI-CV/SYNC Interface A-19054.1 Using the A-190On power up, the A-190 defaults to Performancemode. This is the normal mode of

A-190 MIDI-CV/SYNC InterfaceSystem A - 100doepfer6Pressing the Group button 1 switches to the othermenu group - the button acts as a toggle switch.

doepferSystem A - 100MIDI-CV/SYNC Interface A-1907Changing parametersThere are two ways of changing parameters on theA-190: either manually, or by s

A-190 MIDI-CV/SYNC InterfaceSystem A - 100doepfer84.2 CONFIG menusCHANNEL / REF. NOTEThe CHANNEL parameter sets the MIDI receivechannel. In perf

doepferSystem A - 100MIDI-CV/SYNC Interface A-1909CV CHAR.This parameter sets the voltage control characteri-stics of the pitch CV output from the